Introduction to the Field Communicator Features of the MC6

In this short video, Roy gives an introduction to the field communicator features of the Beamex MC6 advanced field calibrator and communicator. The MC6 has communication capabilities with HART, Foundation Fieldbus, and Profibus.

In communicator mode, you have the option to change the units/variables on the device. Afterwards, it is easy to save the configuration to a file to capture each variable in the transmitter at its current state. You can then upload the saved information to your computer for further analysis and documentation.

Discover more related content

How often should instruments be calibrated

Calibration is extremely important. If instruments drift out of their spec­i­fi­ca­tion range, the con­se­quences can be disastrous for a plant, resulting in costly production downtime, safety issues and even inferior quality goods.

Alabama Power, USA – Beamex Case Story

By removing all the manual steps in the workflow, and eliminating all the paper from the dataflow, Alabama Power has realized a documented time savings from 70%, even up to 75% in some cases, on calibrating pressure trans­mit­ters and pressure switches.

Pressure calibration with Beamex POC8 Automatic Pressure controller

How to perform an automated pressure calibration using Beamex POC8 and MC6 advanced field calibrator and com­mu­ni­ca­tor.

How to calibrate HART pressure trans­mit­ters

How to calibrate and trim a HART pressure transmitter with a HART com­mu­ni­ca­tor and how to document the results and print the calibration certificate.

How to calibrate RTD temperature trans­mit­ters

How to calibrate and trim a HART RTD transmitter using a temperature calibrator.

Temperature loop calibration and trim with the Beamex MC6

How to au­to­mat­i­cal­ly calibrate and trim a HART temperature transmitter using the Beamex MC6 calibrator and CMX calibration management software.

How to calibrate a pressure switch

How to calibrate a pressure switch with the push of one button, using the Beamex MC6 calibrator.

In­tro­duc­tion to the field com­mu­ni­ca­tor features of the MC6

In­tro­duc­tion to the field com­mu­ni­ca­tor features of the Beamex MC6 advanced field calibrator and com­mu­ni­ca­tor which has com­mu­ni­ca­tion ca­pa­bil­i­ties with HART, Foundation Fieldbus, and Profibus.

Beamex MC6 in­tro­duc­tion

Beamex MC6 is an advanced, high-accuracy field calibrator and com­mu­ni­ca­tor and offers calibration ca­pa­bil­i­ties for pressure, temperature and various electrical signals.

How to calibrate a Foundation Fieldbus temperature loop

How to calibrate a temperature measurement loop with FOUNDATION Fieldbus transmitter, local display and DCS display using the Beamex MC6 calibrator and Beamex FB temperature block.

How to calibrate a Foundation Fieldbus temperature transmitter

How to au­to­mat­i­cal­ly calibrate a FOUNDATION Fieldbus temperature loop consisting of a temperature element and temperature transmitter with sensor using Beamex MC6 calibrator and Beamex FB150 temperature block.

How to calibrate an analog temperature loop

How to calibrate a temperature measurement loop with analog transmitter, local display and DCS display using the Beamex MC6 calibrator and Beamex FB 150 temperature dry block.

How to calibrate two temperature sensors si­mul­ta­ne­ous­ly

How to use the Beamex MC6 advanced field calibrator and com­mu­ni­ca­tor to au­to­mat­i­cal­ly calibrate two different temperature sensors using two separate temperature blocks.

How to save smart transmitter con­fig­u­ra­tion

How to use the Beamex MC6 to read and save the con­fig­u­ra­tions of a smart transmitter for later need.

Beamex PGPH Pressure Pump in­tro­duc­tion

Generate and measure pressure efficiently with Beamex PGPH, MC6 and an external pressure module.

How to calibrate a pressure transmitter

How to calibrate a pressure transmitter using Beamex MC6 calibrator and Beamex PGM pressure hand pump.

How to calibrate a mul­ti­chan­nel Fieldbus transmitter

How to au­to­mat­i­cal­ly calibrate a FOUNDATION Fieldbus multi-channel temperature transmitter using the Beamex MC6 and Beamex FB temperature dry block.

How to calibrate a pressure measurement loop

How to calibrate a pressure measurement loop containing pressure transmitter and control room display.

How to calibrate Wire­lessHART transmitter

How to au­to­mat­i­cal­ly calibrate a Wire­lessHART temperature transmitter using the Beamex MC6.